RV Lavatory Sink - Oval - 13"x 10 1/4" x 5 1/2" (White)Drop-in ABS/acrylic-capped lavatory camper sink,13" x 10-1/4", white, has a brighter shine and resist stains and scratches better than plastic. Features hold down clips and includes mounting hardware.RV lavatory sink, 13" x 10 1/4" x 5 1/2" , white,  is made from high gloss acrylic backed with fiberglass.  It has a 2"  drain. All mounting hardware is included.  This is designed for top mount or undermount install. Features

• High gloss acrylic is easy to clean and wear resistant
• Fiberglass insulation provides quiet performance, temperature stability and strength
• Easy to install for both new construction and remodel projects
• Simple tab and clip system make installation easy
• Installation instructions include sink cut out dimensions
• Reinforced drain

 Sink dimensions 13" x10 1/4" x 5 1/2" Counter top cut out dimensions are 11.25" x 8.5"Manufactured by Lyon's Industries.Additional Colors: Part Number Size Color 881491 13€ x 10 ¼€ x 5 ½€ Brushed Nickel REPLACING YOUR OLD SINK:No cutting of your existing counter top is necessary. Simply place the sink in the hole and make sure the rim of your new sink rests on your counter top. If you need to adjust the hole size, use a saber saw or keyhole saw then continue with the instructions below.MOUNTING SINK IN A NEW COUNTER TOP:+ Place the sink upside down on the counter top in the desired location.+ With a pencil, trace a line around the outside edge of the sink onto the counter top.+ Remove sink from the counter top.+ Measure in 7/8" and draw new lines inside the first sink outline just drawn. Radius cornersare not required. As a reference please see cut out dimensions on next page for your product.+ Cut out the counter top on this new line.+ Trial fit your sink into the hole, making sure it is centered where you want it.+ Remove sink. Use a good grade of silicone caulk/adhesive and apply a bead under thelip of the sink, then replace the sink in the hole.+ Attach sink to counter top with bolts and clips provided-see below. Hand tighten boltsonly with three rotations. (Fig. 1)IMPORTANT €” Do not over tighten bolts. Sink will damage if bolts are over-tightened.*Note: It's not necessary for the bolts and clips to be installed. Their primary purpose is to hold the sink in place while the adhesive dries. If there isn't clearance for them, follow steps 1-7 and fill sink with water to hold in place while adhesive dries.+ To finish the job, fill any variances between counter top and sink by sealing outside ofsink with a good grade of color-matched or clear silicone caulk/adhesive.+ When installing drain to sink make sure to use a high grade silicone caulk or latex.Do not use plumber€™s putty.CARE AND CLEANING INSTRUCTIONS+ Clean surface with nonabrasive liquid detergent and warm water. Use cleaningproducts such as Soft Scrub Gel®, Comet Gel®, Gel Gloss® or other similar products.+ DO NOT USE ABRASIVE CLEANERS, "steel wool" or wire brushes on surface. Caustic drain cleaners may cause surface damage. Open flames (cigarettes, candles, etc.) may damage surface.+ Surface damage-light scratches, dulled areas, and small cuts and are restored by firstscrubbing with automotive-type white body cleaning compound, such as Meguire's #9Swirl®Remover, followed by an application of Gel Gloss®. Repair Instructions.+ Remember to always use a cutting board or sink protector when using knives or sharpobjects in your sink.+ Recommendation: When pouring boiling water or placing hot pots or pans into the sink, run some cold water simultaneously.WARNING: Some cleaning products are not suitable for use. Read all labels carefully.DO NOT USE if they say €œnot suitable for use with ABS, acrylic or polystyrene€.RV Lavatory Sink - Oval - 13"x 10 1/4" x 5 1/2" (White)